PadlockPay securely withVisaMastercard

Toyota

Items 1 to 12 of 45 total

per page
Page:
  1. 1
  2. 2
  3. 3
  4. 4

Set Descending Direction
  • TOYOTA HILUX KUN26 4WD 2005-on HEAVY DUTY ROADSAFE RECOVERY TOW POINTS

    GENERAL FITTING INSTRUCTIONS & SAFETY GUIDELINES FOR USE OF TOW POINTS

    Tow Points have been designed as matched pairs, supplied in LH/RH for vehicle specific fitment. Your purchase will include high tensile bolts, and any additional, vehicle specific mounting hardware required to ensure secure fitment to vehicles. Correct fitment of these components is critical for yours & others personal safety.

    Each pair of Tow Points is supplied with vehicle specific fitment instructions. These instructions should be followed during fitment to ensure all steps are taken for correct installation, so when required, the points will be at their optimum Working Load Limit (WLL) as stamped. It is the Tow Points themselves as supplied that have been tested to the WLL advised. It is at the vehicle owners discretion for fitment, ensuring that the chassis is adequately designed, constructed and/or rated to suit this application.

    It is recommended that Tow Points are fitted by a qualified mechanic with specialist 4WD knowledge, who has an understanding of your vehicle including weights carried, the style of Bull Bar, general usage etc. as in some circumstances these Tow Points may not be suit- able for your vehicle.

    These Tow Points have not been tested for lifting purposes & should not be used for lifting, the forces applied differ between lifting and straight line pull type recoveries.

    If a recovery is to be performed, it is imperative both recovery points are utilized, ideally with the use of a bridle strap. This will share the load through the front of your vehicle, giving increased strength and safety margins, the use of a bridle strap will also keep all com- ponents tethered in the case of a failure, reducing the risk of serious injury or death.

    Always INSPECT the Tow Points and shackles before each use. Do not use if there are visible signs of damage or wear (including cracking or elongation). Do not exceed the Working Load Limit (WLL) of the shackle or Tow Points. Always STAY A SAFE DISTANCE away from the recovery area – at least 1.5 times the length of the recovery strap. Incorrect use of recovery equipment can result in serious injury or death.

    Always ensure that adequate PREPARATION for the recovery, to minimise the strain on either vehicle, has been undertaken i.e. Digging, Rock placement etc. If you do not understand how to use this equipment safely or are uncomfortable with your abilities in the use of recovery equipment, please complete a course that specialises in four wheel driving & 4WD vehicle recovery.
     TOYOTA HILUX KUN26 4WD 2005-on HEAVY DUTY ROADSAFE RECOVERY TOW POINTS
    $145.00
  • TOYOTA LANDCRUISER 80 100 105 HEAVY DUTY ROADSAFE VEHICLE RECOVERY TOW POINTS

    PART # RP-PAT04

    Off road driving demands for strong, reliable recovery tow points to cope with a huge variety of recovery
    situations. The purpose of a recovery tow point is to provide a safe and secure point from which to recover a
    stuck vehicle.

    There is much confusion amongst 4WD’ers regarding tow points. Unfortunately, this has been exacerbated
    because many modern vehicles are fitted with generic tow points. Generic tow points are not vehicle specific,
    and while rated to 10,000lbs (4.5t) or similar, mounting them is often done by the vehicle owner, who is not in a
    position to ascertain whether the mounting location can handle the loads exerted during a recovery.
    TOYOTA LANDCRUISER 80 100 105 HEAVY DUTY ROADSAFE VEHICLE RECOVERY TOW POINTS
    $137.75
  • TOYOTA HILUX KUN26 HEAVY DUTY ROADSAFE VEHICLE RECOVERY TOW POINTS

    TOYOTA HILUX KUN26 HEAVY DUTY ROADSAFE VEHICLE RECOVERY TOW POINTS
    TOYOTA HILUX KUN26 HEAVY DUTY ROADSAFE VEHICLE RECOVERY TOW POINTS
    $145.00
  • TOYOTA 120 SERIES PRADO HEAVY DUTY ROADSAFE VEHICLE RECOVERY TOW POINTS TO SUIT ARB BULLBAR

    Tow Points have been designed as matched pairs, supplied in LH/RH for vehicle specific fitment. Your purchase will include high tensile bolts, and any additional, vehicle specific mounting hardware required to ensure secure fitment to vehicles. Correct fitment of these components is critical for yours & others personal safety.

    Each pair of Tow Points is supplied with vehicle specific fitment instructions. These instructions should be followed during fitment to ensure all steps are taken for correct installation, so when required, the points will be at their optimum Working Load Limit (WLL) as stamped. It is the Tow Points themselves as supplied that have been tested to the WLL advised. It is at the vehicle owners discretion for fitment, ensuring that the chassis is adequately designed, constructed and/or rated to suit this application.

    It is recommended that Tow Points are fitted by a qualified mechanic with specialist 4WD knowledge, who has an understanding of your vehicle including weights carried, the style of Bull Bar, general usage etc. as in some circumstances these Tow Points may not be suit- able for your vehicle.

    These Tow Points have not been tested for lifting purposes & should not be used for lifting, the forces applied differ between lifting and straight line pull type recoveries.

    If a recovery is to be performed, it is imperative both recovery points are utilized, ideally with the use of a bridle strap. This will share the load through the front of your vehicle, giving increased strength and safety margins, the use of a bridle strap will also keep all com- ponents tethered in the case of a failure, reducing the risk of serious injury or death.

    Always INSPECT the Tow Points and shackles before each use. Do not use if there are visible signs of damage or wear (including cracking or elongation). Do not exceed the Working Load Limit (WLL) of the shackle or Tow Points. Always STAY A SAFE DISTANCE away from the recovery area – at least 1.5 times the length of the recovery strap. Incorrect use of recovery equipment can result in serious injury or death.

    Always ensure that adequate PREPARATION for the recovery, to minimise the strain on either vehicle, has been undertaken i.e. Digging, Rock placement etc. If you do not understand how to use this equipment safely or are uncomfortable with your abilities in the use of recovery equipment, please complete a course that specialises in four wheel driving & 4WD vehicle recovery.
    TOYOTA 120 SERIES PRADO HEAVY DUTY ROADSAFE VEHICLE RECOVERY TOW POINTS TO SUIT ARB BULLBAR
    $145.00
  • TOYOTA HILUX 05-- HEAVY DUTY ROADSAFE RECOVERY TOW POINTS WITH BRIDLE & SHACKLES

    TOYOTA HILUX 05-- HEAVY DUTY ROADSAFE RECOVERY TOW POINTS WITH BRIDLE & SHACKLES
    TOYOTA HILUX 05-- HEAVY DUTY ROADSAFE RECOVERY TOW POINTS WITH BRIDLE & SHACKLES
    $225.00
  • HEAVY DUTY ROADSAFE TOYOTA FJ CRUISER RECOVERY TOW POINTS

    Tow Points have been designed as matched pairs, supplied in LH/RH for vehicle specific fitment. Your purchase will include high tensile bolts, and any additional, vehicle specific mounting hardware required to ensure secure fitment to vehicles. Correct fitment of these components is critical for yours & others personal safety.

    Each pair of Tow Points is supplied with vehicle specific fitment instructions. These instructions should be followed during fitment to ensure all steps are taken for correct installation, so when required, the points will be at their optimum Working Load Limit (WLL) as stamped. It is the Tow Points themselves as supplied that have been tested to the WLL advised. It is at the vehicle owners discretion for fitment, ensuring that the chassis is adequately designed, constructed and/or rated to suit this application.

    It is recommended that Tow Points are fitted by a qualified mechanic with specialist 4WD knowledge, who has an understanding of your vehicle including weights carried, the style of Bull Bar, general usage etc. as in some circumstances these Tow Points may not be suit- able for your vehicle.

    These Tow Points have not been tested for lifting purposes & should not be used for lifting, the forces applied differ between lifting and straight line pull type recoveries.

    If a recovery is to be performed, it is imperative both recovery points are utilized, ideally with the use of a bridle strap. This will share the load through the front of your vehicle, giving increased strength and safety margins, the use of a bridle strap will also keep all com- ponents tethered in the case of a failure, reducing the risk of serious injury or death.

    Always INSPECT the Tow Points and shackles before each use. Do not use if there are visible signs of damage or wear (including cracking or elongation). Do not exceed the Working Load Limit (WLL) of the shackle or Tow Points. Always STAY A SAFE DISTANCE away from the recovery area – at least 1.5 times the length of the recovery strap. Incorrect use of recovery equipment can result in serious injury or death.

    Always ensure that adequate PREPARATION for the recovery, to minimise the strain on either vehicle, has been undertaken i.e. Digging, Rock placement etc. If you do not understand how to use this equipment safely or are uncomfortable with your abilities in the use of recovery equipment, please complete a course that specialises in four wheel driving & 4WD vehicle recovery.
    HEAVY DUTY ROADSAFE TOYOTA FJ CRUISER RECOVERY TOW POINTS
    $145.00
  • TOYOTA LANDCRUISER 105 HEAVY DUTY ROADSAFE VEHICLE RECOVERY TOW POINTS

    TOYOTA LANDCRUISER 105 HEAVY DUTY ROADSAFE VEHICLE RECOVERY TOW POINTS
     TOYOTA LANDCRUISER 105 HEAVY DUTY ROADSAFE VEHICLE RECOVERY TOW POINTS
    $145.00
  • Ford Ranger Px PX2 Black Hawk Upper Control Arms

    The evolution of the Blackhawk UCA’s…

    When a vehicle has raised suspension (this can be anything from 30mm or above) it will disrupt the vehicles relationship with factory set geometry and create issues such as…

    Reduced caster correction – causing vague steering and response
    Bump steer resulting in reduced handling – with an out of control feeling
    Clearance issues to suspension & wheels/tyres – larger wheels can hit suspension components
    Some standard vehicles can have an issue of the UCA hitting the coil on full droop
    Strength of OE equipment in off road scenarios


    The Blackhawk UCA’s have been designed in conjunction with industry experts to ensure vehicle fitment is comprehensive. During the development process a large number of potential issues associated with lift were identified, and subsequent features were built into the product to overcome of offset them.

    Features standard to the Blackhawk UCA’s are:

    3 degrees of fixed Caster correction Roadsafe have identified this as the perfect amount of correction required for lifts ranging from 30-70mm. By providing a bulk, fixed amount of caster, this offers the ability to utilise the factory adjustment to fine tune the caster required for the vehicles lift, with the UCA not being the limiting factor for increased droop relative to the other components.
    Camber change to meet OE spec, if your application requires increased camber, we can offer offset bushings to provide more camber.
    Clearance to larger aftermarket wheels & tyres – we often see larger than standard size tyres with wheel offsets having clearance issues to the OE UCA, our Blackhawk UCA’s minimise this as much as possible.
    Clearance to suspension components & chassis – a large number of OE UCA’s hit the coil or the chassis mounts on during the suspension travel limiting the amount of travel you can achieve, with revised bends and clearances identified the Blackhawk UCA’s will not contact the strut or the chassis limiting travel unless specifically designed to do so.
    Fixed position ball joint – Blackhawk UCA’s do not use an adjustable ball joint. With a fixed location ball joint we are able to offer OE specification for the ball joint itself.
    The position of the ball joint housings have been rotated to ensure the ball joint is not the limiting factor with maximum down travel. Roadsafe specifically chose a fixed ball joint for a number of reasons – in off road applications the ball joint receives a large amount of “bump” loads, which over time can either knock an adjustable ball joint out of position leading to increased tyre wear due to a change in caster. Changing from a fixed ball joint mount reduces the structural integrity of the mount and the mounting platform of the ball joint, with any remote traveling we need to ensure strength and reliability is not compromised.
    There will never be a need to adjust or re-adjust your caster once established with the Blackhawk arms as the ball joint cannot be knocked out of position.
    Maintain OE specification ball joint & bushings – regardless of where you may go, if you need to replace a ball joint or bushing you can use genuine replacement parts or aftermarket OE specification replacement items, regardless of how remote you are at home or abroad.
    Ball joint binding – Often we see the ball joint limiting the amount of down travel because the OE ball stud hits the side of the ball joint housing, this creates a stress point on the ball stud creating an environment for potential terminal failure of the ball joint, it also limits the amount of down travel possible when used in conjunction with aftermarket suspension and longer shock lengths.
    Securing ABS lines – we incorporate tabs and mounts where practical so the OE lines can be secured discreetly where possible, reducing the potential of sticks and other debris from damaging the sensitive lines.
    Increased strength compared to the OE design – The design of the Blackhawk arms have shown with the use of FEA to be much stiffer than the OE arms, providing the driver with increased handling and response when the Blackhawk arms are fitted when compared to the OE arms, this is illustrated by the amount of deflection the FEA results have provided, with 3 times less deflection in the Blackhawk UCA’s. Does this rigidity negatively transfer to the vehicle? – No, because the Blackhawk UCA’s use OE Rubber bushings, any NVH (Noise, Vibration and harshness) is absorbed in the rubber bushings before it makes it way to the chassis, you may find an increase in wear in the bushings which is directly related to how you drive the vehicle, the bushings are a consumable component of any vehicle, however you should expect years of trouble free service before you should need to replace the bushings.
    Heavy Duty Long life Ball joints – Roadsafe 4wd specially redesigned the OE ball joint into a more robust design, due to the nature of the application the 4wding community requiring a serviceable component. Subsequently Blackhawk UCA’s have a ball joint that is manufactured in the “hard to hard” style with a locating nylon disc that the ball stud terminates against, grease is pumped into the assembly through the top keeping everything lubricated and keeping any potential contaminants out of the boot region. The ball studs and seat area of the housing are all heat treated forming a hardened surface with the purpose of long life and limited wear.
    Dust Cap – Blackhawk UCA’s that utilise a press in ball joint feature a machined alloy dust cap, black anodized incorporating the Blackhawk logo, to deter corrosion. The cap position results in creating a sealed housing to protect the greasable top section of the ball joint from the elements such as water, dust & mud.
    Finish – All arms are sand blasted upon completion and E coated black for a durable discreet finish. E coating is the same process the vehicles manufacturer used for the original equipment you are replacing.
    Ford Ranger Px PX2 Black Hawk Upper Control Arms
    $750.00
  • TOYOTA 150 SERIES PRADO HEAVY DUTY ROADSAFE VEHICLE RECOVERY TOW POINTS TO SUIT ARB BULLBAR

    Tow Points have been designed as matched pairs, supplied in LH/RH for vehicle specific fitment. Your purchase will include high tensile bolts, and any additional, vehicle specific mounting hardware required to ensure secure fitment to vehicles. Correct fitment of these components is critical for yours & others personal safety.

    Each pair of Tow Points is supplied with vehicle specific fitment instructions. These instructions should be followed during fitment to ensure all steps are taken for correct installation, so when required, the points will be at their optimum Working Load Limit (WLL) as stamped. It is the Tow Points themselves as supplied that have been tested to the WLL advised. It is at the vehicle owners discretion for fitment, ensuring that the chassis is adequately designed, constructed and/or rated to suit this application.

    It is recommended that Tow Points are fitted by a qualified mechanic with specialist 4WD knowledge, who has an understanding of your vehicle including weights carried, the style of Bull Bar, general usage etc. as in some circumstances these Tow Points may not be suit- able for your vehicle.




    These Tow Points have not been tested for lifting purposes & should not be used for lifting, the forces applied differ between lifting and straight line pull type recoveries.

    If a recovery is to be performed, it is imperative both recovery points are utilized, ideally with the use of a bridle strap. This will share the load through the front of your vehicle, giving increased strength and safety margins, the use of a bridle strap will also keep all com- ponents tethered in the case of a failure, reducing the risk of serious injury or death.

    Always INSPECT the Tow Points and shackles before each use. Do not use if there are visible signs of damage or wear (including cracking or elongation). Do not exceed the Working Load Limit (WLL) of the shackle or Tow Points. Always STAY A SAFE DISTANCE away from the recovery area – at least 1.5 times the length of the recovery strap. Incorrect use of recovery equipment can result in serious injury or death.

    Always ensure that adequate PREPARATION for the recovery, to minimise the strain on either vehicle, has been undertaken i.e. Digging, Rock placement etc. If you do not understand how to use this equipment safely or are uncomfortable with your abilities in the use of recovery equipment, please complete a course that specialises in four wheel driving & 4WD vehicle recovery.
    TOYOTA 150 SERIES PRADO HEAVY DUTY ROADSAFE VEHICLE RECOVERY TOW POINTS TO SUIT ARB BULLBAR
    $150.00
  • Toyota Landcruiser 200 Series Adjustable Roadsafe Rear Panhard Rod APR015


    An absolute necessity on all raised 4WD’s is the Adjustable Panhard Rod. Designed to correct axle alignment, the fitment of an Adjustable Panhard Rod eliminates potential contact between tyre and body, and improves handling issues on vehicles lifted 2”+. All Roadsafe Adjustable Panhard Rods are Heavy Duty, single thread off car adjustable and come complete with bushings and steering damper mounting brackets where applicable. The majority of Roadsafe Adjustable Panhard Rods now come standard with high flex Rubber Bushings. This has been a gradual change based on customer demand. Our Roadsafe rubber bushings bring the factory ride feel to the upgraded replacement Adjustable Panhard Rods. The high flex Roadsafe rubber bushings offer less Noise, Vibration & Harshness over the polyurethane bushings for panhard applications.
    Toyota Landcruiser 200 Series Adjustable Roadsafe Rear Panhard Rod APR015
    $269.50
  • Toyota Landcruiser 200 series Black Hawk Upper Control Arms

    The evolution of the Blackhawk UCA’s…

    When a vehicle has raised suspension (this can be anything from 30mm or above) it will disrupt the vehicles relationship with factory set geometry and create issues such as…

    Reduced caster correction – causing vague steering and response
    Bump steer resulting in reduced handling – with an out of control feeling
    Clearance issues to suspension & wheels/tyres – larger wheels can hit suspension components
    Some standard vehicles can have an issue of the UCA hitting the coil on full droop
    Strength of OE equipment in off road scenarios


    The Blackhawk UCA’s have been designed in conjunction with industry experts to ensure vehicle fitment is comprehensive. During the development process a large number of potential issues associated with lift were identified, and subsequent features were built into the product to overcome of offset them.

    Features standard to the Blackhawk UCA’s are:

    3 degrees of fixed Caster correction Roadsafe have identified this as the perfect amount of correction required for lifts ranging from 30-70mm. By providing a bulk, fixed amount of caster, this offers the ability to utilise the factory adjustment to fine tune the caster required for the vehicles lift, with the UCA not being the limiting factor for increased droop relative to the other components.
    Camber change to meet OE spec, if your application requires increased camber, we can offer offset bushings to provide more camber.
    Clearance to larger aftermarket wheels & tyres – we often see larger than standard size tyres with wheel offsets having clearance issues to the OE UCA, our Blackhawk UCA’s minimise this as much as possible.
    Clearance to suspension components & chassis – a large number of OE UCA’s hit the coil or the chassis mounts on during the suspension travel limiting the amount of travel you can achieve, with revised bends and clearances identified the Blackhawk UCA’s will not contact the strut or the chassis limiting travel unless specifically designed to do so.
    Fixed position ball joint – Blackhawk UCA’s do not use an adjustable ball joint. With a fixed location ball joint we are able to offer OE specification for the ball joint itself.
    The position of the ball joint housings have been rotated to ensure the ball joint is not the limiting factor with maximum down travel. Roadsafe specifically chose a fixed ball joint for a number of reasons – in off road applications the ball joint receives a large amount of “bump” loads, which over time can either knock an adjustable ball joint out of position leading to increased tyre wear due to a change in caster. Changing from a fixed ball joint mount reduces the structural integrity of the mount and the mounting platform of the ball joint, with any remote traveling we need to ensure strength and reliability is not compromised.
    There will never be a need to adjust or re-adjust your caster once established with the Blackhawk arms as the ball joint cannot be knocked out of position.
    Maintain OE specification ball joint & bushings – regardless of where you may go, if you need to replace a ball joint or bushing you can use genuine replacement parts or aftermarket OE specification replacement items, regardless of how remote you are at home or abroad.
    Ball joint binding – Often we see the ball joint limiting the amount of down travel because the OE ball stud hits the side of the ball joint housing, this creates a stress point on the ball stud creating an environment for potential terminal failure of the ball joint, it also limits the amount of down travel possible when used in conjunction with aftermarket suspension and longer shock lengths.
    Securing ABS lines – we incorporate tabs and mounts where practical so the OE lines can be secured discreetly where possible, reducing the potential of sticks and other debris from damaging the sensitive lines.
    Increased strength compared to the OE design – The design of the Blackhawk arms have shown with the use of FEA to be much stiffer than the OE arms, providing the driver with increased handling and response when the Blackhawk arms are fitted when compared to the OE arms, this is illustrated by the amount of deflection the FEA results have provided, with 3 times less deflection in the Blackhawk UCA’s. Does this rigidity negatively transfer to the vehicle? – No, because the Blackhawk UCA’s use OE Rubber bushings, any NVH (Noise, Vibration and harshness) is absorbed in the rubber bushings before it makes it way to the chassis, you may find an increase in wear in the bushings which is directly related to how you drive the vehicle, the bushings are a consumable component of any vehicle, however you should expect years of trouble free service before you should need to replace the bushings.
    Heavy Duty Long life Ball joints – Roadsafe 4wd specially redesigned the OE ball joint into a more robust design, due to the nature of the application the 4wding community requiring a serviceable component. Subsequently Blackhawk UCA’s have a ball joint that is manufactured in the “hard to hard” style with a locating nylon disc that the ball stud terminates against, grease is pumped into the assembly through the top keeping everything lubricated and keeping any potential contaminants out of the boot region. The ball studs and seat area of the housing are all heat treated forming a hardened surface with the purpose of long life and limited wear.
    Dust Cap – Blackhawk UCA’s that utilise a press in ball joint feature a machined alloy dust cap, black anodized incorporating the Blackhawk logo, to deter corrosion. The cap position results in creating a sealed housing to protect the greasable top section of the ball joint from the elements such as water, dust & mud.
    Finish – All arms are sand blasted upon completion and E coated black for a durable discreet finish. E coating is the same process the vehicles manufacturer used for the original equipment you are replacing.
    Toyota Landcruiser 200 series Black Hawk Upper Control Arms
    $750.00
  • Roadsafe 4wd Recovery Soft Shackle Sb035- 9000kg Rated


    Roadsafe 4wd Soft Shackle Sb035- 9000kg

    SOFT GRIP SHACKLE


    Roadsafe Soft Shackles are designed to be a safe, light weight, easy to use alternative to
    conventional steel bow shackles.Australian made from UHWMPE 10mm 12
    strand synthetic rope, as used in a range of winch ropes supplied by Roadsafe, the
    Roadsafe soft shackles are supplied complete with high visability abrasion
    resistant sheaths, and pre-tensioned for immediate use.
    By using a Roadsafe soft shackle you effectively remove a very heavy and
    potentially lethal standard steel shackle from your recovery system.
    Being manufactured from rope the Roadsafe soft shackle floats, so no more lost shackles in
    muddy, watery environments during recovery, and is flexible, so suitable for a huge
    variety of applications.Rope Spliced Breaking Strain 10mm – 9000kgs
    Testing of the Soft Shackle is undertaken & each batch is coded for traceability.
    Roadsafe 4wd Recovery Soft Shackle Sb035- 9000kg Rated
    $69.00

Items 1 to 12 of 45 total

per page
Page:
  1. 1
  2. 2
  3. 3
  4. 4

Set Descending Direction